Ti6Al4V钛合金表面Al2O3颗粒改性微弧氧化涂层制备及性能

微弧氧化技术是一门新的表面处理技术,在很多领域有着广泛的应用前景,但其结构受限于电解液成分。本文通过在磷酸盐电解液中加入Al2O3陶瓷颗粒,使得在Ti6Al4V钛合金表面的微弧氧化涂层结构和性能得到改性。涂层的结构和性能通过扫描电镜和XRD衍射仪进行表征和测试,涂层的抗高温氧化性能和热震性能通过高温热循环氧化试验和热震试验进行测试。结果表明,通过在电解液中添加Al2O3陶瓷颗粒,涂层由Al2TiO5 and TiO2组成,涂层更为致密,表现出更为优异的抗高温氧化和热震性能。电解液中游动的Al2O3陶瓷颗粒在微弧氧化过程中被吸入到样品表面并进入涂层,涂层的结构和性能得到改性。     

Effect of particle size and grain composition on two-dimensional infiltration process of weathered crust elution-deposited rare earth ores

The two-dimensional infiltration experiment was carried out by means of digital image technology. The evolution process of the wetting body was described. The wetted front distance and the time show a very significant power function relationship. The horizontal wetted distance is larger than the vertical wetted distance in the initial stage. Then, the vertical distance of the wetted body gradually approaches to the horizontal distance. The infiltration distance decreases as the content of fine particles increases. The wetted front migration rate curve shows a three-stage change law, and it increases with the increase of coarse particle content. The directional velocity ratio is defined. The initial value of horizontal infiltration rate is larger than that of vertical one, and then the vertical infiltration rate is gradually close to the horizontal value. The empirical relationship between the characteristic particle size and the stable infiltration rate is established, which provides a theoretical basis for the prediction of the stable infiltration rate in in-situ leaching.     

Experimental characterization of liquid film behavior during droplets–polyethylene particle collision

Nowadays, the droplet–particle collision characteristics in the gas-phase ethylene polymerization process are still unclear. The high-speed photography and a quasi-circle imaging approach are employed to study the collision interaction characteristics between liquid droplets and polyethylene particles. The liquid film evolution is studied through variations of the film thickness on the particle north pole, the dynamic contact angle, center angle and film thickness at the maximum extension. Results have found that for n-hexane the threshold temperature of the recoil happening increases with increasing initial Weber number, but for 1-hexene it is stable. Over 70°C evaporation and splash occurs immediately. Under low Weber numbers, the water droplet stays for damping oscillations, the reference stable height of which is linearly related to temperatures. Moreover, three regimes of film thickness variation with time are identified and mathematically described, while Regime 3 characteristics are found strongly dependent on the liquid species, Weber number, and particle temperature.     

Dissolution kinetics of alumina in molten CaO–Al2O3–FetO–MgO–SiO2 oxide representing the RH slag in steelmaking process

In order to effectively remove alumina inclusions suspending in ultra-low C steel during RH process, the dissolution kinetics of alumina in molten CaO–Al₂O₃–Fe_tO–MgO–SiO₂ oxide was investigated. A crucible dissolution technique was used where the alumina crucible was allowed to dissolve in the slag of various conditions ((% CaO)/(% Al₂O₃), (% Fe_tO), temperature). The obtained data were interpreted using a kinetic mass transport equation to obtain the mass transport coefficient (k_m) in each condition. Increasing (% CaO)/(% Al₂O₃), (% Fe_tO), and temperature increased the dissolution rate as well as the k_m provided that the slag composition is not close to its saturation composition by alumina. In order to simulate the dissolution of alumina inclusion in the RH slag, which cannot be measured by a confocal scanning laser microscopy (CSLM) at present due to the opaqueness of the slag, the modified invariant interface approximation was employed. Along with the obtained k_m, the viscosity of slag, and a reference experiment using the CSLM, the dissolution kinetics of alumina inclusion in the Fe_tO-containing RH slag was predicted. The time required for the dissolution of alumina inclusions from liquid steel to RH slag was discussed.     

HVOF喷涂WC-12Co粒子沉积行为分析

目的 研究不同超音速火焰喷涂条件下WC-12Co粒子在45^#碳钢基体上的沉积变形行为。方法 基于Johnson-Cook塑性材料模型与Thermal-Isotropy-Phase-Change热材料模型，采用LS-DYNA进行建模分析。结果 不同喷涂参数下，WC-12Co粒子在45^#碳钢基体上的沉积行为存在明显差异。沉积过程中，粒子等效塑性应变幅度高于基体;粒子边缘位置等效塑性应变幅度高于粒子中心轴线位置;粒子初始速度与初始温度的增加有助于提升结合界面温度与粒子扁平化程度;粒子初始温度与粒子初始速度对接触界面能量变化影响程度基本一致，单位粒子初始速度与温度提升的能量贡献比 分别为0.78以及0.76，二者的能量贡献比近似相同;适度的基体预热( =500 K)可以促进粒子变形，加深沉积坑深度，增大粒子与基体的结合面积，有助于提升粒子与基体之间的结合强度。基体过冷( =300 K)将导致粒子“翘曲”，降低粒子与基体之间的结合面积，基体过热( =600 K)将导致二者结合处于不稳定状态，易引起粒子剥落，二者均不利于粒子与基体的有效结合。结论 一定范围内提升粒子初始速度、温度与基体初始温度，可以提高粒子扁平化程度，增大粒子与基体结合面积，提升粒子与基体的结合性能，进一步提高涂层质量。     

粒度级配对神华煤成浆特性影响的试验研究

为了研究粒度级配对神华煤成浆特性的影响,通过筛分和干法调浆,探讨了不同粒度分布煤粉的成浆性,结果表明:在添加剂用量为0.3%(干基/干煤)时,具有连续级配特征的原始煤粉可制备出质量分数为61%的煤浆;利用筛分法,分别去除原始煤粉中0.045 mm以下、0.045 mm^0.15 mm、0.15 mm^0.3 mm和0.045 mm^0.3 mm部分,得到4种具有不连续级配特征的样品,其所制煤浆流变性发生了较大变化,其中去除0.045 mm^0.3 mm部分的样品的成浆质量分数提高了3个百分点,在黏度符合要求的前提下流动性大幅提高;连续级配和非连续级配的煤浆均存在黏度与流动性不统一的现象,当级配中粗细颗粒粒径差较大且细颗粒含量达到一定值时,这种现象更加明显。采用粒度级配技术制浆,其细颗粒含量存在一个合理的区间。     

A facile pathway to prepare molybdenum boride powder from molybdenum and boron carbide

Molybdenum boride is an ideal hard and wear-resistant material. In this study, a new method is proposed for preparing molybdenum boride, by which Mo first reacts with B₄C to generate the mixture of molybdenum boride and C, and then the product is decarburized by molten Ca to generate CaC₂. Pure molybdenum boride could be obtained after acid leaching to remove the by-product CaC₂. According to the experimental and thermodynamic calculation results, it is concluded that the single-phase MoB could be successfully prepared, while Mo₂B, Mo₂B₅, and MoB₄ could not be synthesized by this method. Moreover, it was found that the particle size of finally prepared MoB is determined by particle size of raw Mo powder. The residual carbon content of the product could be decreased to 0.10 wt% after first reaction at 1673 K for 6 hours and then decarburization reaction at 1673 K for 6 hours.     

基于SVM的煤与瓦斯突出预测模型及应用

为有效预测矿井内煤与瓦斯突出的危险程度,对其影响因素做了分析与探讨,分别构建了基于粒子群优化算法以及遗传算法支持向量机的煤与瓦斯突出预测模型,并且通过实例对两种模型预测的准确性进行了验证。分别利用单项以及综合指标、BP神经网络以及PSO-SVM模型、GA-SVM模型,对寺河煤矿二号井的突出区域进行预测比较。结果表明,PSO-SVM的预测模型不仅可以在小样本数据中预测出煤与瓦斯突出程度的大小,而且综合预测结果更加精确,其在解决矿井内煤与瓦斯突出的小样本数据中显示出更加强大、通用的性能。     

Characteristics of pigments,modification, and their functionalities

Novel treatments of pigments with inorganic materials have tremendous industrial and commercial prospects. Specific treatment of pigment has a marked effect on its behavior during application. The treatment allows a broad modification of the surface characteristics of pigment particles which leads to improved functionalities. Surface modification of pigments is achieved via coating, polymerization with modifying reagent, treatment with derivatives or polymers, which alter either the optical, conductivity or dispersibility during processing and application. These and many other distinguishing factors that affect the characteristics of pigments such as the class, crystal structure, particle morphology, particle size, hiding power, pigment volume concentration, surface character, and surface treatment have been reviewed. Various organic pigments such as those from fungus and bacteria, and the various families of pigment types such as metallic pigment, light interference, and diffractive pigments which presents decorative quality such as leafing, nonleafing, pearlscent, and Fabry‐Perot effects on substrates have also been reviewed in addition to those from inorganic sources with emphasis on the structure and physiochemical modifications using metal and nonmetal Ions.